Air and forced drying industrial coatings with fast drying and high hardness. Specialty coatings for glass, precious metals and plastics. It is used as air drying coating systems Viacryl SC 200/40X is mainly used for fast drying industrial paints. The dried films are noted for very high hardness and excellent resistance poperties e.g. against water and diluted acids. For air-dried systems (tack-free in 15 minutes) Viacryl SC 200 can be used alone or in combination with plasticizers. Such systems compared with systems using Viacryl SC 200 as sole binder show better pigment wetting and flexibility. The use of plasticizers will, however have a negative influence on alkali resistance. The compatibility of Viacryl SC 200 with other coatings ingredients should be controlled from time to time. Stoving enamels For stoving systems Viacryl SC 200 is generally formulated with plasticizers and urea or melamine resins. The following ratios habe proven successful: Viacryl SC 200 : amino resin : plasticizer = 70 : 15 : 15 or 65 : 15 : 20 (on solids). Compared with air drying systems such systems show after curing (e. g. 30 min/140 °C) improved flexibility, hardness, impact and chip resistance. Specialty coatings For air drying as well as stoving systems Viacryl SC 200 can be used to formulate specialty coatings with good adhesion to glass, precious metals, and various plastics such as ABS and polyphenylene oxide (PPO).

SETATHANE D E 2767 is applied in combination with aromatic polyisocyanates based on diphenylmethane diisocyanate as binder for solvent-free two-component polyurethane coatings with high chemical resistance for concrete and other porous substrates, fillers, sealing compounds and synthetic resin mortars. SETATHANE D E 2767 is suitable for the formulation of coatings, mortars and sealers with high chemical resistance. Coatings formulated with SETATHANE D E 2767 generally exhibit outstanding resistance to organic and inorganic acids, alkalis and solvents. Over-cross linking of 50 % and more is usual. This allows a wide-ranging variation in flow and chemical resistance. To ensure blister-free curing, SETATHANE D E 2767 requires the addition of hydrated lime in accordance with DIN EN 12 518 (or cement if necessary) as a CO2 scavenger. In certain cases where the film thickness is less than 100 μm, there is no need to add hydrated lime.

TUNGOPHEN B NV is applied as an additive in alkyd coatings. Additions of 1 - 3% TUNGOPHEN B NV, calculated on the 100% alkyd resin, greatly accelerate the through-drying and increase the gloss of alkyd coatings. Initial drying slows in proportion to the addition of TUNGOPHEN B NV. This improves the flow properties of the coating and reduces the likelihood of surface defects, even in thicker films. TUNGOPHEN B NV is usually added at room temperature as a solution in xylene. The addition of TUNGOPHEN B NV results in yellowing. For this reason, it should not be used in white coatings. The amount used in pale-colored coatings should be kept to a minimum. Addition of the product to coatings based on medium-oil alkyd resins, e.g. Setal A F 48, will result in particularly significant acceleration of through-drying. TUNGOPHEN B NV should not be used in styrenated alkyd resins, oil based coatings or oil/resin combination coatings.

VIACRYL SC 121/60X is a sole binder for road-marking paints. Fast drying primers and top coats for nonferrous metal and plastic substrates.It is used as road-marking paints Viacryl SC 121/60LG was especially developed as sole binder for road-marking paints. Road-marking paints based on this copolymer have excellent adhesion and abrasion resistance, permanent flexibility as well as good whiteness retention. It is, however, recommended to first conduct a trial application under the given conditions to ensure suitability. Coating of plastics One-coat paints based on Viacryl SC 121 show especially good adhesion to plastics such as PVC, acrylic sheet, polycarbonate and polyester reinforced components.Primers and top-coats on metallic substrates. In view of its fast initial and through drying as well as its good water resistance Viacryl SC 121 is suitable for formulation one-coat paints and industrial primers. Coatings based on this product show good adhesion to steel, aluminium and zinc. For aluminium substrates a binder pigment ratio of about 1 : 2 should be selected. For steel a ratio of 1 : 1.5 is recommended. Decorative finishes are generally pigmented in ratios of 1 : 1 (binder/pigment) on solids.